Search Results for ‘transmission’

Hey y’all- attempted to remove and replace the transmission pan gasket this past weekend. I was easily able to access all bolts but the two located behind the crossmember. I eventually loosened the trans mount bolts on the crossmember, and was able to barely remove the bolts, however, getting...

I was hoping someone may be able to help me, I have finally got my GMC C15 ready to drive and took it on a road test and the damn thing wont shift out of first gear either in automatic or manual shifting. I did my research and found it could either be the modulator or the Governor, I have...

Hi all, I have a 1966 C10 with a small block and power glide. Previous owner switched from a power glide to a 4 speed with a floor shifter. I'm converting back to the power glide and need a few parts to complete the job. 1 :The spring and shifter handle located on the steering column. and 2...

Hey to all, I'm building a 1971 chevy c10. I bought the truck in really good running conditions, but definitely needs plenty of body work. The other day I noticed a pretty substantial oil slick under the truck. I thought the engine had a pretty good leak. Finally getting the chance to check...

I have a 1964 C10 shortbed that I plan to go with a small block and a 700R4 behind it. Can anyone tell me whether I need a long tail piece or a short one on the transmission? Will either one work when I will need a custom driveshaft anyway? Are the earlier 700R4's easier to install with less...

Last week my Dad was driving his 1970 C20, not realizing it leaked oil he ran it dry. When I get home in the fall I'm going to help him pull the motor and do a rebuild. I want to make a part list before I get home so we are ready to go when it comes time. I would like your help identifying the...

Hello My 1963 automatic transmission shifts hard from the first to the second gear I have to accelerate hard so that it switches from the first to second gear. do you have any ideas?

I have a 62 Chevy c10 I'm restoring. It's currently frame off and I'm having difficulties removing the 3 speed from the bell housing. I have removed the tail shaft, trans mounting bolts and side cover/shifter assembly. I can't seem to get it to come off the guide pins. I've pried on it over and...

I picked up a 61 C10 in fairly good condition. I have replaced the wheel cylinders, clutch slave cylinder and master cylinder. While under the truck, I saw the speedometer drive gear and housing were not there. The hold down bolt had been broken off in the tail shaft and the hole for the gear...

I have a 40p sbc and i need to replace my tranny. The original is a sm420 but i was wondering if its possible to use something like a TH350? Is this possible? Will i run into any problems?

Hey there. Im at the point in my build where i need to send my transmission out to be re-built. However i dont know what lind of tranny i have exactly. I know i have a "4 on the floor" but have no idea on the actual specifications of the tranny. I was able to disconnect and pull it out...

I just bought a my first classic truck, a 1961 C10 Apache. I want to replace the stock 3 speed with a manual 5 or 6 speed transmission. What recommendations do you all have will allow for me to keep the bench seat? I also need recommendations on headers that the collector box won't drag the...

I've got a 1968 C10 with a 327 that's got around 370-410 hp and unknown amount of torque (guessing the same). It currently has a TH350 3-speed auto in it and a 2.?? rear diff. I wanted to see what suggestions y'all had for a swap that would better fit this engine and hp output. The transmission...

I've got a 1968 C10 with a 327 that's got around 370-410 hp and unknown amount of torque (guessing the same). It currently has a TH350 3-speed auto in it and a 2.?? rear diff. I wanted to see what suggestions y'all had for a swap that would better fit this engine and hp output. The transmission...